Repairs to uPVC Windows

uPVC is a fantastic choice for modern homes. They are durable, long-lasting and easy to maintain. They do not decay or rust as aluminum or timber.

Regularly cleaning and lubricating UPVC windows and doors is vital. This will help prevent unnecessary repair costs and improve energy efficiency.

1. Broken Glass

If the glass in your window is damaged, it could cause a large deal of damage to your home, which can make it very dangerous and potentially fatal. It is important to ensure that your windows are in good condition.

Single-pane windows are relatively simple to replace and typically fit into frames that were previously in use very easily. However If you have double-pane windows that are secured by internal beading, it'll be more difficult to take out the panes that are in place and replace them with new ones. In this situation it is essential to purchase plastic spacers to aid in fitting the new pane into the window frame.

If you're planning to attempt to remove the window panes yourself it is crucial to wear appropriate safety gear, including thick gloves and eye protection. It is also a good idea to lay down a dropcloth before you start working on the glass so that any shards fall onto the fabric instead of landing on the floor where they can be trampled upon and cause further damage.

Once the glass has been removed from the window, it's best to seal the gap with packaging tape or duct tape to block drafts and water from entering the property until a professional comes out and repair the window. This also serves as a barrier to prevent any criminals from getting into your home. If the gap is particularly large, you might think about the security door with an integrated window, as it will provide the best of both worlds.

2. Sagging

uPVC windows and doors are a cost-effective, durable and energy-efficient alternative to timber sash windows. As time passes, they may be affected by a variety of issues that include sagging. A sagging uPVC window can cause problems with light, draughts, and even security. It's crucial to act when you discover that your uPVC windows are falling down.

Repositioning the hinges could help fix a window that is sliding. First, you'll need to unblock the windows to access the frame. Then, remove both the top and bottom hinges using a screwdriver, and then adjust them clockwise or counter-clockwise. Once you've adjusted the hinges, close the window and test it for fitting. If you're satisfied with the fit of your window, tighten the screws to secure them in the right position.

If you can't reposition the hinges, you may need to replace the seal. Over time rubber seals can lose their elasticity and dry out which causes their tightness to decrease. It is crucial to replace your seal as quickly as you can to ensure that your uPVC window watertight and draughtproof.

uPVC handles may also become loose. This is usually due to screws that have been removed over time, but it can be caused by the handle mechanism wears out. Fortunately, it's easy to fix the handle of a window that is loose yourself. First, you'll need to close the window and then perform an initial fitting. The joint at the corners of the sash should align with the joint on the casing. If it isn't then you can make use of a screwdriver to loosen the handle and then turn the mechanism back into its original position.

3. Water Leaks

It is important to take action if you get up each morning to discover mouldy walls and floors that are wet. Water leaks from windows are not just a cause for destruction of your home's structure but also hinder your efforts to control the temperature inside your home. The most common cause for leaking uPVC windows is that the sealant around the frame is either damaged or missing.

It is a fairly easy fix that can be done by any DIY expert. Based on the severity of the issue the caulking that was used up might need to be removed before a fresh layer can be applied. It is crucial to keep in mind that when it comes to uPVC window repairs, do not be tempted to 'over-caulk in order to make the area more difficult to clean and could decrease the efficiency of your energy usage.

Check that any drainage holes are free of debris in them, and also that the sill pan has been angled correctly to drain away from the window. In more serious situations, you may have to replace the window.

Mold spots and rotted sills are other signs of water leakage. This fungus thrives in damp conditions and is able to quickly spread throughout the house.

If the leakage occurs between the double glazing repairs-glazed glass, it is more likely the issue is with the seal rather than the frame. A uPVC specialist can easily fix this problem by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

Hinges could be at fault when your uPVC window is difficult to open or it opens with an ease. They can be repaired by any skilled DIYer and can usually be done within a few minutes.

Like any mechanical part, hinges can be damaged over time. It is an easy process but it can be easier if you have someone to help you hold the frame up.

It is also worth checking that the uPVC hinges are opening and closed in the right direction. You can do this by checking for the arrows on each hinge, this indicates which way the window should be opened.

The issue could be caused either due to opening the window in the wrong way or a faulty installation in the factory. Sending us photos via our website is often enough to solve the issue. We are more than happy to give assistance.

It is also crucial to ensure that the hinges are lubricated regularly. Applying an engineering lubricant that is light to the hinges is a great method to accomplish this. We recommend using the lubricant that doesn't contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication can help the window operate and close more smoothly. It also helps prevent corrosion and reduce the risk of sticking. It is recommended to do this once a year. WD40 and other solvent-based fluids are not recommended since they could damage parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by a few different things. The hinges, also due to wear and tear may become displaced, which causes an opening to appear where the sash meets the frame. These can be easily repaired by giving them good clean, but in the event that they are beyond repair it might be necessary to have them realigned or replaced. Secondly the interlock, this is located on the hinge of the window, can be misaligned. Again, it may be feasible to give them a good clean, window repairs but in some cases it might be necessary to get them replaced.

These seals can wear down or get damaged over time, allowing air escape. Replacement of these with high-quality weatherstripping is a good way to stop draughts. Replace the windows made of upvc with low-emissivity glass. This will help to regulate indoor temperatures and lessen draughts.

Another, and most effective ways to cut down on the draughts in your home is to use a draught excluder. These are typically made of fabric which are filled with a kind of filler. They can be put on top of your windowsill. They will keep your home warm by blocking out cold air.

With a little regular maintenance and repair windows made of upvc will provide an excellent level of security and insulation for your home. It is crucial to realize that all windows have a lifespan and there may come a point where it is more cost-effective to replace them rather than repair them. So, if you are experiencing issues with your Upvc windows, it's recommended to seek assistance from a professional as soon as you can.