Double Glazing Door Lock Repairs

Have your uPVC window or door mechanism started to fail? Maybe the window or door handles don't meet up properly or are hard to use.

It is crucial that the double glazed doors function smoothly, or else you will lose energy and increase the likelihood of burglary. Owen the Locksmith will be able to repair your door lock at a reasonable cost.

Snapped Key

It can be quite frustrating when a key is snapped into a lock. This can also be a security risk, as it may make you vulnerable to a burglar if the door does not lock. There are a few easy fixes you can make to fix the problem and make your door work again.

Keep calm. If you get scared and start doing a lot of fumbling around you could end up pushing the broken piece of the key further into the lock, making the situation worse.

Spray WD-40, or any other penetrating lubricant, into the lock. This will allow the broken piece come out more easily. You can also use a screwdriver to help break up any pieces stuck that might be blocking the way. If you have a piece of the key stuck out then grab it using a paperclip or other thin metal object and pull it. Both of these methods work well, however, be careful not to push the damaged piece of the key further into the keyway.

Some paperclips have grooved edges that can work in a pinch to extract hooks and some jigsaw blades are also suitable for this function. If you don't happen to have any of these items, you can bend a hook using needle-nosed pliers. Finally, you can use a pair of tweezers grasp and pull out the remaining pieces of broken keys.

If you cannot remove the broken piece of key Use a lock deicer. It's usually available at most hardware stores. It is used to freeze any water or ice that could be inside the lock.

If none of these solutions seem to work, it could be time to consult a locksmith. The experts at Fitlocks can quickly solve problems like broken handles or snapped keys using uPVC locks and door Upvc Repairs Near Me mechanisms. They can also reconfigure the double glazing door mechanisms so that they are more easy to operate. You can book an appointment online for a double-glazing repair or contact us to discuss your requirements.

Broken Cylinder

A broken cylinder is a serious security threat. A professional locksmith can easily repair the cylinder. To repair the cylinder, locksmiths will need to tap it. This can be accomplished with a hammer, or any other tool. The best method is to employ a wire or long match. Then, position the end of the match or wire near the keyway. The locksmith can then hit the lock to crack it. This is better than using a hammer that could harm the lock.

The most frequent cause for cylinder head cracks is overheating. This can happen when the block and the cylinder head are made of various metals, such as cast-iron or aluminium. When various metals are heated and cool at different rates, it may create hotspots locally that expand faster than the rest of the cylinder head, thus leading to cracks.

Another possible cause for cylinder cracks is corrosion. When the cylinder head and the block of the cylinder are not properly maintained, it can cause corrosion or rust and cause them to expand at a more than they ought to. This can lead to cracks over time.

If your Upvc Repairs Near Me window or door lock is stiff or requires lots of pressure to turn, this could be due to many things. This issue could result from a defective locking mechanism or misalignment, and also a worn out handle.

Fortunately it's a simple and cost-effective fix for the majority of homeowners of double glazing. A professional locksmith is able to fix this problem within one hour of arriving at the home. They can fix the locking mechanisms, or change the window handles and replace the gearboxes, based on your specific needs. A locksmith with experience will always be able advise you on the most cost-effective solutions for your home. They may recommend upgrading to 3 Star TS007 Euro Cylinders which offer an additional layer of protection against burglars. It's a small amount to enjoy the peace of mind that comes from knowing that your uPVC door is secure.

Broken Handle

Window handle locks have complex mechanisms that deteriorate as time passes and use, so it's not a surprise that they sometimes break. If yours breaks, it can be difficult to pinpoint the cause of the problem and make sure you fix it correctly.

Repairing your damaged handle, whether it's the internal locking mechanism or latch, will improve the security of your uPVC door and prevent draughts. It is costly to repair or replace the handle in a way that isn't done correctly. It could also harm the frame and the lock of your door.

Screwdriver: With the window open and the screw loose, loosen the handle. It should be located on the inside face of the back plate, and is normally concealed by a screw cover for aesthetic reasons. You should not lose any internal parts of the handle such as the levers and plates on either side. Ideally, keep these in the same order so you can re-install them when needed.

Then, using another screwdriver take the screw off that connects the handle with the spindle at the back. Once the screw is removed, you should be able to pull the handle off and pull out the broken spindle. Replace it with a new spindle, making sure it's the same length (you can find them online or at hardware stores). Securely screw it in the correct position. Do not overtighten the screw because this could cause damage to the handle and window frame.

Make sure the new handle is fitted, Upvc Repairs Near Me then close and test the handle. It should function smoothly and you'll be able to open your windows once again.

Don't forget to double-check that your uPVC window is shut properly while you're working with the handle. If they don't cause draughts and damp in your home, as well as compromising the efficiency of your home's energy usage. A local window company, like Core Sash Windows, will be capable of adjusting the hinges on your window frames to ensure they are able to shut properly.

Broken Spindle

It is often the case that the spindle within a handle breaks rather than the handle itself. This is particularly common with uPVC tilt-and-turn windows. These types of windows require a handle which operates a locking mechanism in the window frame. The handle is attached a central rod that activates a series of locks that are shaped like mushrooms and secure the window frame keep. If the dead latch mechanism does not open when the handle has been turned, it's likely the spindle is broken. This can be a problem that is frustrating.

There are ways to fix this issue. A skilled locksmith can quickly and efficiently solve the issue. A reputable locksmith can disassemble the handle of the window by using a tool that removes the wheel portion that houses the spindle. This is done without causing any damage to the handle or causing other damage to the frame of the window.

After the wheel has been removed, the technician will inspect the spindle and determine what has caused it to break. This involves breaking the spindle into its component components and carefully observing their general condition as well as any particular areas of damage or excessive wear. This process is typically performed in a clean room by skilled technicians.

The next step is to clean the damaged spindle, this will remove any dirt or other debris that might be obstructing its normal functioning. After that, the spindle could be repaired or replaced. If it is being replaced the technician can take a dowel of a similar size to the original and drill mating holes in both pieces of the spindle. This will ensure that the spindle will fit perfectly with the handle.

If the spindle is damaged and cannot be repaired it may require replacement completely. Home centres sell generic substitutes, but if your window style is rare you'll have to speak with an expert in cabinet making or woodworking who can make the exact part. Once the new spindle is installed, it can be fitted to the handle by line up the holes for screws in the handle with the frame's existing screws. Once the handle is securely seated, you can operate your uPVC windows.