Repairs to uPVC Windows

uPVC is a fantastic option for modern homes. They are long-lasting, durable and easy to maintain. Unlike timber and aluminium, they are not susceptible to rust or rot.

It is important to clean and oil UPVC windows and doors regularly. This will reduce costly repairs and increase energy efficiency.

1. Broken Glass

If the glass in your window is damaged, it could cause a large deal of damage to your home, making it extremely dangerous and possibly fatal. You should take the time to make sure that your windows are in good shape.

For single pane windows, it can be relatively simple to replace windows, and the new one will usually fit inside the old frame very easily. If you have Double Glazing Croydon-paned windows which are held together by internal beading, it will be difficult to remove and replace the panes that were previously in use. In this case, it is necessary to buy plastic spacers to help the new pane fit into the window frame.

Wearing protective eyewear and thick gloves is essential when you are planning to remove the glass by yourself. It is also recommended to lay down a drop cloth before you begin working on the window panes, Double Glazing Croydon so that any shards of glass fall onto the fabric and not onto the floor, where they could be trampled under.

Once the glass is removed and the glass is removed, it's a good idea to seal the gap with packaging tape or duct tape to stop drafts and water from entering the home until a professional can come out and repair the window. It also acts as a barrier to prevent any intruders from making their way into your home. If the gap is particularly large, you might think about a security door that has an integrated window, since this will offer the best of both worlds.

2. Sagging

uPVC is a durable energy-efficient, cost-effective and economical alternative to timber sash window. However, over time, they may be afflicted by a variety of issues like sliding. A window that is sagging can cause problems with light, draughts and even security. If you notice that your uPVC window is beginning to lose its shape, it is important to act swiftly to stop the issue from worsening.

Repositioning the hinges could help fix a window that is sagging. First, you'll need to unblock the windows to get at the frame. Then, using an screwdriver, remove the hinges on the top and bottom and adjust them by turning them clockwise or counter-clockwise. Once you've repositioned the hinges, close your window and test it for fitting. If you're satisfied with the fit, tighten the screws to ensure they stay in place.

If you are unable to move the hinges, you might need to replace the seal. Over time, rubber seals lose their elasticity and become dry which causes their tightness to decrease. If this happens, it's important to replace the seal as fast as possible to ensure your uPVC windows remain watertight and safe from drafts.

uPVC handles could also become loose. This is usually due to screws that have been removed over time, but it can also be due to the mechanism of the handle wears out. Luckily, it's not difficult to repair a loose uPVC window handle yourself. You'll first need to close the window and do an experiment fitting. The joint at the corners of the sash should be aligned with the joint on the casing. If it does not then you can use the screwdriver to loosen the handle. Then, turn the mechanism into position.

3. Water Leaks

If you awake to damp floors and mouldy walls each time it rains, it's crucial to take action. Leaks of water from windows can cause structural damage to your home and affect your ability to regulate the temperature of your home. Most often, uPVC window leaks are caused by a damaged or double Glazing Croydon missing sealant.

This is a simple fix that can be accomplished by any DIYer who is competent. Depending on the severity of the problem the old caulking may require removal before a fresh layer can be put on. When it is time to uPVC repair, you must avoid over-caulking. This will only make your window more difficult to clean and decrease its energy efficiency.

Verify that the drainage holes are free of debris in them and ensure that the sill pan is angled correctly to drain away from the window. In more serious cases, you may need to replace the window.

Mold spots and rotten sills are also signs of water leakage. This mold thrives in damp environments and can quickly spread across the house.

It is also important to keep in mind that if the leakage originates from the glass of your double-glazed windows it may be more likely to be an issue with the glass seal rather than the frame or sagging. Again this can easily be fixed by an uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or are loose and blow open with a breeze It could be hinges at fault. These are easily replaced by any competent DIYer and are usually done within a few minutes.

Like all mechanical parts hinges are prone to wear out over time. The process of replacing a hinge on a window is essentially a very simple process but it can be easier to do if you have someone to assist in holding the frame in place.

Make sure that the uPVC hinges are open and closed in the proper direction. You can do this by looking for the arrow on each hinge. This shows which way the window should be opened.

The problem with the hinges on windows could be the result of incorrectly opening the window a certain way or by inadequate installation at the factory. Sending us photos through our website can often resolve the problem. We are more than happy to provide advice.

Regularly lubricating the hinges is also necessary. Applying an engineering lubricant that is light to the hinges is a good method to accomplish this. We recommend using the lubricant that doesn't contain solvents, like 3-in-1 Multi-Purpose oil. Regularly lubrication will help the window to open and close more easily. It can also reduce the chance of windows sticking and help prevent corrosion. This should be done at least every year. WD40 or other solvent-based oils should not be used as they could damage your uPVC windows.

5. Draughts

Draughts in upvc windows can be caused by a variety of different factors. The hinges may also become misaligned due to wear, causing a gap between the frame and sash. They can be repaired by giving them a good clean, but when they're beyond repair, it could be necessary to get them aligned or replaced. Secondly the interlock, this is located on the hinge of the window and can also become misaligned, again it is possible to give them a clean but in certain cases, it may be necessary to have these replaced.

These seals can wear down or become damaged over time, allowing air to escape. Installing high-quality weatherstripping is a good way to keep draughts at bay. Another alternative is to replace the window repairs Kingsbury with low-emissivity glass, which will help regulate indoor temperatures, and also reduce the possibility of draughts.

The final method to cut down on the amount of draughts is to use a Draught-exclusion device. These are typically fabric tubes filled with a filler that can be put on top of your window sill. These will help to stop cold air from entering and keep your home warm and cozy!