How to Replace a UPVC Window Handle

If your upvc window handle is damaged, don't be concerned. Replacing a window handle made from upvc is an easy task and replacement windows can be completed in just a few steps.

It doesn't matter if you have an in-line or a cranked espagnolette window handle they all have a square spindle that protrudes out of the back plate. The spindle is placed into the locking device.

Identify the type and size of the handle and lock.

Over time, window handles and locks may be damaged or lose their functionality. The good news is that this can usually be repaired without replacing the entire uPVC window unit. One of the first things you need to do is identify the type of lock and handle you have to determine the parts will be required for replacement.

You can identify the kind of handle by looking at the base. There is a screw or pin holding the handle to its base. If the screw is gone, it could be an indication that the handle has split from the base section. If the handle is broken internally and isn't able to hold onto the spindle anymore It could also be an indication that the handle should be replaced.

There are many uPVC handles that are available, but the Espag handle is the most common. They are usually secured with two bolts and have a spindle that engages the lock mechanism in the frame of the window. These handles are commonly used on tilt and turn uPVC windows.

Another kind of uPVC window handle is the Cockspur handle. These are similar to the Espag handle, however they are a little further from the frame. These handles are generally used on older uPVC window frames.

Venetian window handles are a different option. They are similar to Espag handles but have a flat bottom that allows them to be installed flush with the frame. These handles are a great choice for homeowners looking for an elegant handle that will blend in with their uPVC frames. They are available in a range of colors that can be matched to any style.

Take a measurement of the spindle

It is important to know how the handle is installed before you can order a replacement. This will determine whether it's tight enough or loose and if it's able to fit inside the window frame. This can be done by identifying the type of handle and determining the spindle's measurement. The spindle is the steel shaft that connects the handle to the lock in the window frame. The spindle comes in various sizes. The current standard for the industry is 8mm. Older handles could have a 9mm cross-section, so it's crucial to measure the old one to ensure you get the correct size replacement.

There are several types of window handles. However, the most common are inline Espagnolette and Cockspur handles. These handles are used to operate a locking system inside the window. They utilize shootbolt rods to lock the window after it has been closed. Depending on the type of handle they are secured in place by screws or pins.

You can find replacement handles for windows made of upvc on the internet and in many DIY stores. They are available in a variety of finishes and are suitable for new and replacement windows. For added security they can be key-locking or a non-locking fire escape.

To take off your old handle, open the window and remove the screws that secure it. Be careful not to cause damage to the screws and put them in a container for future use. Once the screws have been removed, carefully pull out the handle and take a measurement from the base to the top of the spindle. This will provide you with the information needed to buy the correct replacement. The spindle of the handle is the shaft of steel that connects it to the lock gearbox within the window glass replacement near me frame.

Remove the old handle

Switching the handle of an uPVC handle is a straightforward job that takes less than five minutes if you have the appropriate tools. The first step is to determine the kind of lock and handle that will help you identify the right replacement. After that, weighing the spindle will make sure that the new handle is a perfect for the job. The handle that was used previously needs to be removed and replaced with the new one.

Most uPVC handles have inline Espagnolette handles. These handles feature an internal spindle that slots into the locking mechanism of the window. These are generally easy to take off, but you may need to use force when they're stuck. There are usually two screws that keep the handle in place, which can be removed using either pliers or a screwdriver. Depending on the kind of handle, you might also have to remove any pins holding it in place.

After removing the screws you can take off the handle you were using previously. The top of the base plate will be visible when the handle is in the open position, revealing two screws you can remove. If the sticker is visible, you'll have to take it off.

Utilizing the screws from the handle, you are now able to screw the new handle into the appropriate position. Make sure the handle is in an open or unlocked position, then align the screw holes with the ones on the window. After you have done this, replace the cap screws. Test the new handle. It's simple to swap a uPVC handle, but you need to make it right.

Fit the new handle

It's time to put in your new handle if you've successfully removed the old handle from the frame. Begin by locating and removing the screw covers with your screwdriver. After they've been removed, put them in a safe place and proceed to the next step.

Then screw the spindle into by aligning it with the hole that is already in place. Be sure to align the holes in the handle with holes in the window frame and use a screw similar in length to the ones previously used or it could cause the handle to not being secure.

uPVC Espag handles come with a 7mm square spindle that turns the lock mechanism that is attached to the window. This style of handle is found in the majority of modern uPVC Windows. uPVC Cockspur (also known by the name Cotswold) handles have an extended, curved nose that locks onto the frame's outer or cross member of the transom bar. They are usually found on older uPVC Windows.

It is essential to lock and unlock the window a few times after the handle is installed. If everything goes according to plan, the replacement uPVC handle should be securely attached and working smoothly. If you encounter any issues these steps will assist you identify the issue and fix it swiftly. If you're struggling with your uPVC handle or have any other glazed home improvement issues do not hesitate to contact us at Bridgewater Glass for professional assistance. Our glaziers have been trained to repair or replace a variety of window frames and handles, making us an excellent choice for your double-glazing requirements.

Test the new handle

As time passes and through regular use over time, uPVC locks and handles may be damaged and wear and wear and tear. They can become less secure and effective and therefore it is important to replace them as soon as possible. It's also recommended to do this when you upgrade your windows, as changing your lock and handle will maintain the integrity of the windows you have just bought.

There are many different styles of uPVC window handles. Some are attached by pins or screws while others are fitted with blades that slide into the lock mechanism. Each type has its own method of replacement, so it is important to know which type you have before working on it.

Espag window handles are the most popular kind, and are typically found on newer uPVC windows. The spindle extends from the handle into the lock gearbox and triggers the locking mechanism when you open the window. They're also easy to remove however, you must take care not to damage the mechanism or the handle while doing so.

Cockspur window handles are another popular option for uPVC windows. The locking mechanism is activated when the window is closed or tilted. A spur attaches to the striker plates in the shape of wedges on the frame. This type of handle is more difficult to repair than other types, but it's still an excellent choice for the majority of homes.

Venetian handles are joined by two bolts, and they have a low projection on the frame. This is different from the Espag handle. These handles are perfect for those who want to have a flush handle that blends in with uPVC window frames. These are great for both commercial and residential properties.